Realistic Dinosaur Puppet Manual
Ultimate guide on how to use our dinosaur puppet step by step
Any problem with how to wear, and how to operate the puppet?
No worries, we will walk you through on this page.
1. Unboxing
Step 1: Get a knife.
Step 2: Remove the iron wires from the lock.
Step 3-5: Open the box and take out the puppet & accessories.
Accessories：
①: Bubble Wrap, ②: Puppet, ③: Sound Box, ④: Glove, ⑤: Packing Bag.
2. How to Clean the Skin
After the painting completes, the skin looks “bright”, which is not realistic. Thus we put some “Chalk Powder” to make it look matt.
When you receive the puppet, please follow the steps below to get it clean.
Step 1: Prepare a piece of foam or towel.
Step 2: Get it wet with clean water.
Step 3: Wipe up the puppet.
3. Check the Electrical Devices
Here are the electrical devices:
①: Battery, ②: Remote Control, ③: Connector, ④: Sound box, ⑤: USB Cable.
Step 1: Connect the connector to the sound box (red for positive, black for negative).
Step 2: Connect the connector to the battery.
Step 3: Press the remote control to see if the sound box works well.
Recommended Battery Specifications:
Remote Controller Battery: 12V, 23A lithium battery.
Sound Box Battery:12V NiMH Battery.
4. How to Put on the Puppet
Step 1: Get a puppet.
Step 2: Insert the sound box into the glove.
Step 3: Spread out the glove.
Step 4: Put the glove on your hand.
5. How to Install Wings (ONLY for Dragon Puppet)
Required Tools: ①: Dragon Puppet, ②: Wings, ③: Nipper Plier, ④: Screws, ⑤: Spring.
Step 1: Insert the wing into the hole
Step 2: Align the upper and lower holes.
Step 3: Install the screws (install the bigger screws in the hole on the top).
Step 4: Install the spring.
Step 5: Tuck the excess fabric into the wings.
6. How to Operate
For the Dinosaur Puppet:
Upper Handle: for eyes blinking.
Lower Handle: for the mouth movements.
For the Dragon Puppet:
Upper Handle: for eyes blinking.
Lower Handle: for the mouth movements.
Handles in the Back: for wings movements.
7. How to Operate Sound Box
Step 1: Install batteries in the remote control.
Step 2: Connect the battery to the sound box.
Step 3: Press the buttons and the baby dinosaur starts to roar (six kinds of sounds).
8. How to Change Sound Files
Required Tools: The sound box and a USB cable.
Step 1: Connect the sound box to the computer by USB cable.
Step 2: Open the sound box folder.
Step 3: Click on the application in the red box.
Step 4: Click “Add voice”-“ADD”.
Step 5: Select the replacement sound files.
Step 6: Choose “Update” and click “UPDATE”.
9. How to Charge
Step 1: Connect the charge with the battery.
Step 2: Connect the charge to the socket.
10. How to Maintain
Required Tool: De-rust Lubricating Spray.
Only the welded joints need to be sprayed.
Please spray the joints from this hole. So the long beak won’t influence anything.
Step 1: Put the nozzle through the opening into the interior of the pterosaur.
Step 2: Spray the joints following the video.
11. How to Retouch the Color
Required Tools: ①: gasoline, ②: clear silicone, ③: brush, ④: paper cup, ⑤: acrylic paint (according to the color you need).
Step 1: Mix gasoline and silicone at a ratio of 5:2.
Step 2: Add paint to the gasoline mixture and mix it with paint at a ratio of 4:1.
Step 3: Mix them evenly, and then take a piece of clean foam.
Dip it in a little paint to wipe on the faded area.
Finally, put the puppet in a ventilated place to dry for 2 hours.
